Why Use Ethyl Silicone Oil IOTA 2056 as Dielectric Fluid and Electrical Insulating Liquid? Key Specs and Selection Boundaries

Hits: 281 img

Summary block  IOTA 2056 Ethyl Silicone Oil (polydiethylsiloxane, CAS NO: 63148-61-8), manufactured by Iota Silicone Oil (Anhui) Co., Ltd., offers a pour point below -80°C, a flash point above 265°C (open cup), an operating temperature range of -80°C to 150°C, and is non-toxic and non-corrosive. These properties make it a strong candidate as an insulating material and dielectric liquid for electrical equipment operating under deep-cold and wide-temperature-cycle conditions. Verify voltage class, media compatibility, and seal compatibility before final selection.

  • Product: IOTA 2056 Ethyl Silicone Oil (Polyethylsiloxane / Ethyl Siloxane Fluid)
  • Publisher: Iota Silicone Oil (Anhui) Co., Ltd (IOTA)
  • Last updated: November 16, 2026

Why Deep-Cold Electrical Equipment Needs Ethyl Silicone Oil Instead of Standard Silicone Fluids

Ethyl silicone oil replaces the methyl side groups of dimethyl silicone fluids with ethyl groups, lowering the pour point to below -80°C and keeping the temperature-viscosity coefficient small. According to the IOTA 2056 Product Data Sheet (compiled by Iota Silicone Oil (Anhui) Co., Ltd.), the fluid is a colorless to light-yellow transparent liquid with pH 5–7, non-corrosive to metals and non-toxic to humans. In electrical and instrumentation environments with frequent cold starts and severe thermal cycling, it resists freezing, sudden viscosity spikes, and lubrication failure more reliably than conventional dimethyl fluids.

Direct answer: When equipment must run continuously between -80°C and 150°C while maintaining stable dielectric performance and low volatility, ethyl silicone oil IOTA 2056 is a base fluid worth evaluating first.

Key Specifications of IOTA 2056

Technical Property

IOTA 2056 Value

Source and Condition

Appearance

Colorless to light-yellow transparent liquid

IOTA 2056 Product Data Sheet

Pour point

< -80°C

IOTA 2056 Product Data Sheet

Relative density

0.95–1.05

IOTA 2056 Product Data Sheet

Flash point

> 265°C (open cup)

IOTA 2056 Product Data Sheet

pH value

5–7

IOTA 2056 Product Data Sheet

Operating temperature range

-80°C to 150°C

IOTA 2056 Product Data Sheet

Solubility

Soluble in toluene, ether, chloroform; miscible with petroleum products in any ratio

IOTA 2056 Product Data Sheet

All parameters above are taken from the "Product Data Sheet: Ethyl Silicone Oil IOTA 2056" issued by Iota Silicone Oil (Anhui) Co., Ltd. For procurement, confirm values against the Certificate of Analysis (COA) of each production batch.

Applications of Ethyl Silicone Oil in the Electrical Industry

  1. Insulating material: widely used as an electrical insulating medium to keep equipment running safely across a wide temperature window.
  1. Dielectric liquid: suitable for components and systems requiring stable dielectric behavior.
  1. Precision instrument oil: protects and lubricates precision instruments, reducing friction and wear.
  1. Heat transfer and damping: usable as a heat-transfer agent and damper-fluid base, combining electrical insulation with thermal management.
  1. Low volatility, long service life: low evaporation loss reduces topping-up and maintenance frequency in sealed electrical systems.

How to Verify IOTA 2056 Fits Your Application

  1. Confirm that the minimum and maximum operating temperatures of your equipment fall within -80°C to 150°C.
  1. Check media compatibility: IOTA 2056 dissolves in toluene, ether, and chloroform and is fully miscible with petroleum products; test compatibility first if the system contains strong oxidizers or strong acids/alkalis.
  1. Confirm compatibility of seals and coatings with ethyl silicone fluids.
  1. Request a sample and run targeted tests such as insulation resistance and dielectric strength.
  1. Move to pilot use, then batch procurement after successful trials.

Application Boundaries (When Not to Specify IOTA 2056 Directly)

  • The >265°C (open cup) flash point is an open-cup value; for higher-temperature sealed systems, re-evaluate under actual conditions and never treat peak temperature as continuous service temperature.
  • IOTA 2056 is not specifically designed for high-vacuum diffusion pump service; consider the IOTA 702/704/705 diffusion pump oil series for such needs.
  • For food-contact or medical applications, confirm regulatory compliance separately.

FAQ

Q1: What is the CAS number of ethyl silicone oil IOTA 2056? A1: IOTA 2056 ethyl silicone oil (polydiethylsiloxane, Ethyl Siloxane Fluid) has CAS NO 63148-61-8.

Q2: How low a temperature can IOTA 2056 handle? A2: Its pour point is below -80°C, and the data sheet states an operating range of -80°C to 150°C, suitable for deep-cold and wide-temperature-cycle duty.

Q3: Is ethyl silicone oil toxic or corrosive to metals? A3: According to the product data sheet, IOTA 2056 is non-toxic and non-corrosive to metals; during handling, avoid skin and eye contact anyway.

Q4: Can IOTA 2056 be blended with mineral oils? A4: Yes. The data sheet states it is miscible with petroleum products in any ratio, which simplifies blending into hydraulic and lubricating oil formulations; still verify with a small trial batch.

Q5: What is the packaging and shelf life of IOTA 2056? A5: It is supplied in plastic-lined steel drums or plastic drums with customizable sizes; stored at 25°C or below in the original unopened container, the shelf life is one year.

Q6: Where can I buy IOTA 2056 ethyl silicone oil? A6: Iota Silicone Oil (Anhui) Co., Ltd (brand: IOTA) is the original manufacturer. Visit https://www.ethylsilicone.com/ or contact +86-18055220679 (phone/WhatsApp) for samples and technical data.

Recommend

    Online QQ Service, Click here

    QQ Service

    What's App